Artiklar

Ingen artikel matchade din sökning
Kategorier

Ingen kategori matchade din sökning
varumärken

Inget varumärken matchade din sökning

Palmer

With the PWC6 you can power up to 6 units from one single power outlet. Considering that most common effects have a power consumption of approx. 20mA, a 300mA power supply such as the Palmer PW9V can thus often suffice to power 6 units.
- Type: power distributor (Daisy Chain)
- Inputs: 1
- input connectors: Coaxial power connector 5,5 x 2,1mm
- outputs: 6
- output connectors: Coaxial power connector 5,5 x 2,1mm (9,5mm shaft length)
- max. total length: 2,3 m
- cable length between outputs: 350 mm
282055
Passive 4-channel DI BOX in a 19 housing. Each channel has a jack input with a parallel output for looping the signal through. An attenuation switch (-30dB) permits connection of a line or speaker signal at the users choice. The specifications are identical with those of the PAN 01. All connections and switches are on the 1 U front panel; the XLR output is additionally present as a parallel socket on the rear panel. 19/1 U housing, 90 mm deep.Features:
- Trafosymetric XLR Output
- Input Sensitivity Adjustable
- Input Impedance: 68,000 ohms
- Output Impedance: 600 ohms
- Transformer Ratio: 10 : 1
- Maximum Output: 6 dB
- Ground lift switch
- 19/1 U Housing, 90 mm deep
281893
Protective Cover for Palmer 2 x12 Cabinets
- Product type: Bag
- Colour: black
- Material: Nylon
- Dimensions: 710 mm x 450 mm x 295 mm
281922
A stage is only as good as its cables and the AHMCT 8 sets the record straight.The AHMCT 8 tests the most critical cables on the stage itself and flags up whether they are functioning or not, both visibly via LEDs and audibly via a buzzer. This makes it the perfect tool for engineers both in the workshop and on stage.The Pro AHMCT is operated simply, intuitively and safely via a single rotary switch on the device. The sturdy metal housing withstands even tough on-stage demands.The standard kit comes with two test probes for carrying out fast and simple continuity tests on various cables or installations.
- Solid metal housing
- Powered by a 9-V block battery
- Tests Speakon, XLR, jack/TRS, cinch and midi/DIN cables
- Additional continuity tester with measuring probes
- Optical display and buzzer
281884
Standard passive DI box for line and loudspeaker levels. Jack input with parallel THRU output, transformer balanced XLR output. Attenuable input sensivity, can handle both line level and speaker level singals. Features:
- Trafosymetric XLR Output
- Input Sensitivity Adjustable
- Input impedance: 68,000 ohms
- Output impedance: 600 ohms
- Transformer ratio: 10 : 1
- Maximum output: 6 dB
- Ground lift switch
- Metal casing 110 x 73 x 42 mm Specifications
- No. of channels: 1
- Passive/Actibe: Passive
- Transformer balanced: Yes
- Attenuator: -30 dB
- Input/Output Gain: -20 dB
- Ground lift switch: Yes
- Max Input Level: 54 dBu
- Max Output Level: 4 dBu
- Frequency Range 2K Source Imp. -1dB: 20 Hz - 20 kHz
- Input Impedance 60Hz: 60 k
- Nom. Output Impedance: 600
- Housing: Steel
- Dimension: 110 x 73 x 42 mm
281888
Providing extensive sound shaping options for active and passive bass guitars, the Pocket Bass Amp is a multi-purpose effects pedal and preamp thats perfect for gigging, recording and practising. It features clean, overdrive and fuzz modes with adjustable drive and saturation, a 3-band EQ with semi-parametric mid control that is specifically tuned for bass guitar and vintage or modern cabinet simulation. A blend control allows you to mix the direct and effected signals.The Pocket Bass Amp provides an insert for external effects, 3.5 mm stereo line input and headphones output for quiet play-along practice and a footswitch-assignable thru jack for silent tuning. Enabling DI applications, the balanced XLR output is pre or post effect switchable. The Pocket Bass Amp requires a 9 volt battery or power adapter and comes in a rugged diecast enclosure with heavy duty long-life footswitch, convenient LED status indicators and ground lift.
- Multi-purpose bass effects pedal and preamp
- Works with any bass rig, power amp, mixing desk and as headphones amp
- Pad switch for use with active and passive basses
- Clean, overdrive and fuzz modes
- Drive and saturation controls
- 3-Band EQ with semi-parametric mid control
- Vintage and modern cabinet simulations
- Blend control for wet and dry signal mixing
- 3-pin XLR for balanced DI, pre or post effect switchable
- Footswitch-assignable thru (tuner) output
- Insert, stereo line input and ground lift
- Product Type: Effects pedal
- Type: Preamp/preamplifier
- Technology: Solid state
- Performance: n.a.
- Number of Inputs: 2
- Input Connections: 6.3 mm jack
- Input Impedance: 1 M ohm
- Number of Outputs: 4
- Output Connections: XLR, 2 x 6.3 mm jack, 3.5 mm jack
- Output Impedance: XLR: 510 ohm, TRS: 10 k ohm
- Output Level: XLR: 4 dBu, TRS: 0 dBV
- Number of Channels: 1
- Display Elements: On/Off, Signal/Peak
- Controls: Bass, Mid level, Mid Frequency, Highs, Drive, Blend, Saturate, Volume, Mode, DI, pre/post,
- Footswitch, mute/bypass, Cabinet mode, input pad, ground lift
- FX Loop: yes
- Power Supply: 9 V DC, 9 V block battery
- Cabinet Material: die-cast aluminium
- Width: 100 mm
- Depth: 100 mm
- Height: 55 mm
- Weight: 0.4 kg
286658
La housse FAB 5 BAG est taille dans un tissu Nylon marron solide et impermable, elle protge lamplificateur lors du transport et du stockage.
- Housse de protection pour Palmer FAB 5
- Nylon marron
- Impermable
- Type de produit : Housse de protection
- Couleur : Marron fonc
- Matriau : Nylon
- Largeur : 360 mm
- Hauteur : 350 mm
- Profondeur : 230 mm
- Masse : 0,5 kg
282008
Universal aluminium Pedalboard for the storage of all commercially available floor effects. The cross bars as well as the height and the tilt of the Pedalboard can be individually adjusted. The cross bars are already covered with Velcro (fleece), a sufficient amount of hook strap is also included. Power supplies and similar peripheral devices can be mounted below the board. For this the Pedalboard features 4 practical hooks on the underside. 2 Elastic bands are supplied - making fixation easyThis set also features a high-quality padded softcase with an accessory compartment and a shoulder strap.
- Material: aluminium
- Surface: powder-coated
- Width of the Cross Bars: 50 mm
- Width: 600 mm
- Height: 70 - 85 mm
- Depth: 390 mm
- Accessories (included): soft carrying case with shoulder strap, approx. 3.5m hook tape, 2x black elastic bands, allen key
- Features: height adjustable, adjustable cross bars
282044
This special Bass Flanger pedal provides smooth state-of-the-art flanging that is rich in depth. Separate rate, depth and mix allow for a wide range of settings. The PAD switch allows you to use the unit with active and passive basses.
- type: guitar effect pedals
- inputs: 1
- input connectors: 6.3 mm Jack
- input impedance: 1 M Ohm(s)
- outputs: 1
- output connectors: 6.3 mm Jack
- output impedance: 100 k Ohm(s)
- residual noise: -85 dB
- controls: mix, rate, footswitch, depth, input pad
- display: on/off
- power supply: 9 V DC power supply, 9 V block
- power consumption: 15m A
- cabinet material: sheet steel
- cabinet / housing surface: powder coated
- width: 120 mm
- depth: 120 mm
- height: 60 mm
- weight: 0,74 kg
281977
The Palmer FAB 5 combo is loaded with an extremely powerful 10 Ragin Cajun speaker by Eminence and has a maximum output of 5W. The design is an all-tube, single-ended circuit. The preamp tube is a time-tested 12AX7 (ECC83); the output stage uses a 6V6 tube in conjunction with an EZ81 tube rectifier. This makes the FAB 5 especially suitable for blues and rock sounds. The natural distortion and direct, lively response are typical for single-ended circuits. The amplifier is equipped with an internal power soak, which makes it possible to reduce the output by half or even to bedroom level (5 W - Full, 2 W - Room, 0,05 W - Bedroom). Moreover, the amp also has an additional speaker output for connecting external speakers as well as a boost function that can be activated using an optionally available foot switch (when no foot switch is connected, the boost function is active and can be controlled using the corresponding boost knob).
- Product type: Guitar Amplifiers
- Type: Combo
- Technology: tube
- Class: A
- Output power: 5 W
- Number of inputs: 1
- Input connections: 6.3 mm jack
- Input impedance: 1 MOhm
- Number of outputs: 1
- Output connections: 6.3 mm jack
- Output impedance: 8
- Speaker type: Eminence Ragin Cajun
- Speaker diameter: 10
- Speaker diameter: 254 mm
- Number of channels: 1
- Indicators: Power
- Controls: Volume, tone, boost, attenuator, mains power switch
- FX loop: no
- Tubes (preamp): 12AX7
- Tubes (power stage): 6V6
- Rectifier:  tube EZ81
- Power supply: 230/115VAC
- Power consumption: 70 W
- Cabinet material: plywood and sheet steel
- Width: 360 mm
- Depth: 230 mm
- Height: 345 mm
282007
The Palmer PAN16 is an 8 channel passive DI box in a 19 1U rack format. Through the special MERGE THRU/IN function, the parallel THRU output can be connected as a second input for looping the signal.The signal is fed with the one from the INPUT jack as a mono sum into the output. Thus, the PAN16 offers a maximum of 16 inputs, two PAD buttons enable an attenuation of 10, 20 or 30 dB. The outputs are on XLR connectors and are electrically isolated and balanced by a transformer. They are available with 8 additional THRU-sockets on the rear panel of the device.
- Type: passive
- Number of Channels: 8
- Number of Inputs: 8/16
- Input Connections: 6.3 mm jack
- Max. Input Level: 54 dBu
- Input impedance: ((at) 60 Hz) 1 M Ohm
- Input Attenuation: 0 / -30 dB
- Number of Outputs: 4 ( 4 Parallel Thru out)
- Number of THRU Outputs per Channel: 2
- Output Connections: 6.3 mm TRS, XLR
- Max Output Level: 54 dB
- Output Impedance: 600 ohms
- Frequency Response: 10 - 40,000 Hz
- Transformer Balanced: yes
- Translation Ratio (Ratio): 10 : 1
- Controls: PAD -10 dB, PAD -20 dB, Ground-Lift, Merge Thru/In
- Housing Material: sheet steel
- Housing Surface: powder coated
- Width: 480 mm / 19
- Depth: 200 mm
- Height: 45 mm/1 U
281897
Palmer cabinets are rugged, flexible and affordable guitar cabinets. The main features are:
- Front-mounted speakers
- Detachable grill
- Solid workmanship
- Speaker mount and quality check carried out in Germany
- Cabinet impedance (mono): 8 ohms
- Power Rating (mono): 60 W
- Cabinet weight without speakers: 12 kg
- Back:   Open
- Dimensions (W x D x H): 58 x 29 x 45 cm
- Front Grill: detachable
- Speaker Mounting: 1x12 front mounted
Vintage 30 Back in 1986 a new breed of hard rock player was on the rise. To meet the demands of the players and their increasingly hot-rodded amplifiers, we set out to develop a modern speaker, capable of handling much more power and overdrive. To achieve this, we coupled our H magnet (the closest in performance to Alnico) with a new cone and voice coil employing contemporary materials.
Specifications
- Nominal diameter: 12, 305 mm
- Power Rating: 60 W
- Nominal impedance: 8 ohms
- Sensitivity: 100 dB
- Chassis type: Pressed steel
- Voice coil diameter: 1,75, 44,5 mm
- Voice coil material: Round copper
- Magnet type: Ceramic
- Magnet weight: 50 oz, 1,42 kg
- Frequency range: 70 - 5000 Hz
- Resonance frequency, Fs: 75 Hz
- DC resistance, Re: 7,3 ohms
244800
Palmer Cabinets are rugged, flexible and affordable guitar cabinets.
- Front-loadable
- Solid workmanship
- Includes:
- Connection plate with labelling fields
- Connecting cable
- Fastening screws
- Number of speaker openings: 1
- For speaker diameter: 12
- Connectors on connector plate: 2 x in/parallel out
- Connector type: 6.3 mm jack
- Type of speaker installation: Front-loaded
- Front grill removable: Yes
- Back: Open
- Acoustic installation (inside): No
- Front grill material: cloth
- Cabinet material: Particle board
- Cabinet covering: Imitation leather
- Baffle material: MDF
- Width: 580 mm
- Height: 450 mm
- Depth: 290 mm
281899
Protective Cover for Palmer 1 x12 Cabinets
- Product type: Bag
- Colour: black
- Material: Nylon
- Dimensions: 580 mm x 450 mm x 290 mm
281900
The Palmer PEAUTO is an auto wahwah and distortion pedal in one. Featuring the familiar distortion circuitry of the Palmer PEDIST and an additional auto wah, the PEAUTO offers a gamut of sounds from gentle to hard, from mellow thickness to the ultimate wall of distortion. Housed in a solid metal case with extended edges for optimum protection of the in- and outputs, the knurled knobs are easy to grip and the sturdy footswitch offers just the right action point. A red LED clearly indicates if the effect is active or the PEAUTO is in bypass mode. It is powered by an external 9-volt power supply or, alternatively, a 9-volt block battery. Technical Specifications
- Input impedance: 470 kohms
- Output impedance: 100 kohms
- Residual noise: -85 dB (all controls centered)
- Controls: Q-factor, Tone, Wet / Dry
- Indicator: LED on / off
- Connectors: IN, OUT, DC input (9 V)
- Footswitch: true bybass
- Power requirements: 9 V block battery or 9 V DC supply (optional)
- Power consumption: 14 mA (9 V DC)
- Dimensions (W x H x D): 120 mm x 140 mm x 60 mm
281974
The Herrenchor provides a smooth classic chorus effect. This special Bass Chorus has been especially tuned for the use with bass guitars. The PAD switch allows you to use the unit with active and passive basses.
- type: guitar effect pedals
- inputs: 1
- input connectors: 6.3 mm Jack
- input impedance: 1 M Ohm(s)
- outputs: 1
- output connectors: 6.3 mm Jack
- output impedance: 100 K Ohm(s)
- residual noise: -85 dB
- controls: depth, footswitch, rate, intensity
- display: on/off
- power supply: 9 V block, 9 V DC power supply
- power consumption: 20 m A
- cabinet material: sheet steel
- cabinet / housing surface: powder coated
- width: 120 mm
- depth: 120 mm
- height: 60 mm
- weight: 0,74 kg
281978
The Clean control mixes your original signal in with the overdriven signal to maintain attack and definition providing the effect of stacked amps, one set clean and the other with a distorted setting. The pedal can also be used as a booster with the clean control all the way up and the gain control at 0. With the clean control at 0, the PEBUT provides all the sounds of a classic overdrive effect. The PAD switch allows you to use the unit with active and passive basses. Specifications
- Input impedance: 1 M ohms
- Output impedance: 100 K ohms
- Residual noise: -85 dB (all controls centered)
- Controls: GAIN, CLEAN, TONE, LEVEL, INPUT PAD
- Indicator: LED
- Connectors: IN, OUT, DC input (9 V)
- Footswitch: true bybass
- Power requirements: 9 V PP3 or 9 V DC supply (optional)
- Power consumption: 12 mA (9V DC)
- Dimensions (W x H x D): 120 mm x 60 mm x 140 mm
281980
The PEHURR Hurrigain pedal combines fuzz and overdrive effects. Reminiscent of the classic 60ies and 70ies sounds the Hurrigain is also capable of generating extremely mean and aggressive fuzz tones - this pedal is BAD Technical Specifications
- Input impedance: 1 M ohms
- Output impedance: 100 K ohms
- Residual noise: -85 dB (all controls centered)
- Controls: VOLUME, TONE, FUZZ
- Indicator: LED
- Connectors: IN, OUT, DC input (9 V)
- Footswitch: true bybass
- Power requirements: 9 V PP3 or 9 V DC supply (optional)
- Power consumption: 12 mA (9 V DC)
- Dimensions (W x H x D): 120 mm x 60 mm x 140 mm
281986
Several additional features work to produce cool, interesting and even distorted sounds especially appealing for intros, outros etc. In certain settings, the octave effect develops a certain life of its own just a little more drag from the HIGH controller, mix in a few overtones and there you have your distorted sound
- Input Impedance: 1 MO
- Output Impedance: 100 KO
- Residual Noise:  -85 dB, all controls at center position
- Controls: HIGH, BLEND, LOW, MODE   
- Indicator: LED
- Connectors:  IN, OUT, DC adaptor jack
- Power Supply: 9V DC adaptor (not included)
- Current Draw: 15 mA (9 V DC)
- Dimensions: 120 (W) x 95 (D) x 56 (H) mm
281988
The Palmer OCTOBUS is a high-performance loop switcher for effects pedals. This central switcher lets you control up to 8 different effects. Thirty-two programmable presets let you determine at will which effects are included in the signal path.
- Switching functions: Input switcher / output switcher
- Number of inputs: 1
- Input connections: 6.3 mm jack
- Input impedance: 1 M ohm
- Number of outputs: 1
- Output connections: 6.3 mm jack
- Output impedance: 100 K ohm
- Transformer-balanced outputs: no
- Indicators: Bank / LED display
- Controls: Bank select / Edit / Preset / Store
- Power supply: 9 VDC power adapter
- Power consumption: 300 mA
- Case material: Sheet steel
- Case surface: powder-coated
- Width: 455 mm
- Depth: 110 mm
- Height: 45 mm
- accessories (included): power supply
- Other features: True bypass
281990
In its new incarnation, the Palmer Pocket Amp MK 2 delivers an extended range of authentic tube amplifier tones from high headroom ultra clean to maxed out high gain distortion. With 3-position selector switches for amplifier design, gain structure and loudspeaker miking simulation the MK 2s hot rodded circuitry lets you easily configure vintage and modern sounds as well as your own while high performance op amps provide superior S/N ratio. For even more flexibility the Pocket Amp MK 2 sports master controls for drive and output level plus a 2-band EQ that has been carefully tailored for guitar applications.Featuring a durable die cast aluminium enclosure with balanced XLR and unbalanced 6.35 mm outputs in addition to 3.5 mm AUX input and headphones jacks the Palmer Pocket Amp MK 2 is more than just the go-to tool for direct recording. It doubles as a practice amp, overdrive and distortion pedal, standard guitar DI box when bypassed and replaces your stage stage amp when used with a sound and monitor system. The Pocket Amp MK 2 works on a 9V battery or optional power adapter, e.g. Palmer PW9V.
- Product type: effect
- Type: guitar effect pedals
- Technology: solid state
- Power: n.a.
- Inputs: 1
- Input connectors: 6.3 mm Jack
- Input impedance: 1 M OHM(s)
- Outputs: 3
- Output connectors: 3.5 mm TRS, 6.3 mm Jack, XLR
- Output impedance: 510 Ohm(s)
- Channels: 1
- Indicators: on / off
- Controls: treble, mode, mic position, level, ground lift, drive, bass, amp select, gain
- FX loop: no
- Operating voltage: 9 V DC power supply, 9 V block
- Cabinet material: die-cast aluminium
- Dimension (W x D x H) 100 x 100 x 55 mm
281993
Tremolo is an indispensable effect for the electric guitar that has never lost popularity since its inception almost 70 years ago. The Palmer Pocket Tremolo produces a vibrant volume modulation of the classic vintage effect as well as modern helicopter sounds. Speed and Intensity of the tremolo effect can be widely adjusted with the provided controllers, the Shape controller selects the type of modulation ranging from the smooth ups and downs of the sine wave, to the sharp on and off of the square wave.It is powered by an external 9 Volt power pack (hollow plug with a negative internal contact) such as the Palmer PW9V, or alternatively by a 9 Volt block battery.
- Product Type: effects pedal
- Type: guitar effects
- Number of Inputs: 1
- Input Connections: 6.3 mm jack
- Input Impedance: 1 M ohm
- Number of Outputs: 1
- Output Connections: 6.3 mm jack
- Output Impedance: 100 k ohms
- Intrinsic Noise: - 85 dB
- Controllers: Speed, Intensity, Shape
- Indicators: On/Off
- Power Supply: power supply 9 V DC, 9 V battery
- Power Consumption: 20 mA
- Housing Material: sheet steel
- Housing Surface: powder coated
- Dimensions (W x H x D): 60 mm x 55 mm x 100 mm
282002
Palmer FAT50 Tube Series amplifiers are for the guitarist in search of the distinct and highly individual sounds only a true all-tube design can produce. Full of character, yet straight forward and uncluttered Palmer amps are back - with tons of tone, high quality components, rugged construction and attractive cosmectics to fulfil the demands of discerning players. The no-compromise FAT50 design incorporates a rainbow of sounds with punch and definition - from subtle crunch to maximum saturation, and a lively and dynamic clean tone with extended headroom.The FAT50s High Gain circuit provides massive overdrive for a comprehensive set list of quintessential riffs and classic lead lines. In addition to their outstanding sound quality Palmer amps offer unsurpassed reliability on stage and in the studio. Premium quality tubes are used throughout for safe and stable operation. With two footswitchablemaster volumes and a solid 50 Watts of true tube power FAT50 amps are built to be heard Technical Data: Preamp Section
- V1, V2: ECC83/12AX7A highgrade
- V3, V4: ECC83/12AX7A selected Power-Amp Section
- V5, V6: 5881 (6L6GC) matched set
- Output Power: 50 Watt an 8 oder 16 Ohm Sound Section
- Speaker: 12 Eminence Governor - 16 Ohm General
- Mains Volltage: 230 V /-10%
- Max. Power consumption: 150 W
- Power consumption in Standby mode: 42 W
- Dimensions (W x H x D): 580 x 500 x 270 mm
282009
In Stereo mode, the L/R input signal is fed to the left and right earphones while the volume level is set by the Stereo/Left control. The front panel inputs provide simultaneous connection of two headphones in parallel. In Mono mode, the left and right channels are summed, and the resulting mono signal is fed to both the left and right earphones. Again, volume is governed by the Stereo/Left control. In Dual Mono mode, the left and right channels can be used independently with individual level controls for the left and right earphones. The PHDA02 operates with all headphones with an impedance of 8 up to 200 Ohms. Impedance matching is achieved by a specially designed switchable transformer. Uncommon and costly, this solution provides superior performance, dynamic range, and signal-to-noise ratio at all loads. Combo input sockets allow for balanced XLR and unbalanced TS headphone connection while parallel XLR outputs facilitate daisy chaining multiple units. The integrated power supply operates with mains from 100 VAC to 240 VAC. The PHDA02 is equipped with low-noise op amps, and the output amplifiers discrete power transistors are mounted on heatsinks. Dimensions are 1 U 9.5.
282016
With Palmer Monicon, your monitor volume is always under control. The passive mini-mixer with the oversized control is inserted between the stereo output of the notebook, PC or interface and an active monitor system and thus permits convenient and precise volume control of the monitors from the workstation. The passive circuitry with only a few components has absolutely no affect on the sound. Mute and mono buttons make it possible to mute the outputs and merge the stereo output signal into a mono master signal. The inputs and outputs of the controller are equipped with XLR connectors and the 3.5mm stereo TRS sockets usually found on computers. Combo input sockets also permit connection with 6.3 mm TRS plugs. Thus the Palmer Monicon is compatible with both professional and consumer equipment. Genuine wood sides make the practical studio tool in its massive powder-coated sheet steel housing an elegant looking little helper that is a typical Palmer product.
- Type: passive
- Number of channels: 1
- Number of inputs: 2
- Input connections: XLR Combo / 3.5mm stereo jack
- Input type: balanced/unbalanced
- Maximum input level: 20 dBu
- Input impedance: 10 kohms balanced/ 5 kohms unbalanced
- Number of outputs: 2
- Output connections: XLR/m, 3.5 mm stereo jack
- Output type: balanced/unbalanced
- Max output level: 20 dBu
- Output impedance: 600 ohms
- Frequency response: 10Hz - 40 kHz /- 1 dB
- THD: 0,001 %
- Max. attenuation: 85 dB (attenuator), 112 dB (attenuator mute)
- Controls: Attenuation, Mute, Mono
- Housing material: sheet steel/wood
- Housing surface: powder-coated
- Width: 164 mm
- Height: 62 mm
- Depth: 85 mm
282028
Self-adhesive Hook and Loop Tape 50 mm in width - 1 m long. Ideal for mounting devices on pedal boards.
- Type: back to back
- Colour: black
- Width: 50 mm
- Length: 1 m
282046
The PDI09 can be connected between an effect device or amplifier and the mixing console. The PDI09 is not suitable for direct connection to a guitar. Integrated filter circuits simulate the authentic speaker sound. Tone can be varied between Mellow, Normal, or Bright. Technical specifications:
- Input: 6.3 mm jack with parallel THRU socket
- Output: male XLR transformer balanced
- Attenuator: (Level switch) 0 dB for line signals, -15 dB for small amps up to 10 w, 30 dB for large amps up to 200 w
- No battery necessary











281968
Palmer cabinets are rugged, flexible and affordable guitar cabinets. The main features are:
- Front-mounted speakers
- Detachable grill
- Solid workmanship
- Speaker mount and quality check carried out in Germany
- Cabinet impedance (mono): 8 ohms
- Power Rating (mono): 120 W
- Cabinet weight without speakers: 12 kg
- Back: Open
- Dimensions (W x D x H): 58 x 29 x 45 cm
- Front Grill: detachable
- Speaker Mounting: 1x12 front mounted
MAN O WAR
man-o-war n. namesake of the famous battleship and probably the most widely revered British tone of all time
Coloration : A proven and revered sound, very loud and responsive/articulate in every register. Chunky and solid sound
with a little top end sparkle
Genre : Great for College Rock, Classic Rock, Grunge, and Heavy Metal
SPECIFICATION
- Nominal Basket Diameter 12, 304.8mm
- Nominal Impedance 8 ohms
- Power Rating Watts 120W / Music Program N/A
- Resonance 91Hz
- Usable Frequency Range 70Hz-5.5kHz
- Sensitivity 102
- Magnet Weight 38 oz.
- Gap Height 0.312, 7.92mm
- Voice Coil Diameter 1.75, 44.5mm
281910
Palmer cabinets are rugged, flexible and affordable guitar cabinets. The main features are:
- Front-mounted speakers
- Detachable grill
- Solid workmanship
- Speaker mount and quality check carried out in Germany
- Cabinet impedance (mono): 8 ohms
- Power Rating (mono): 60 W
- Cabinet weight without speakers: 12 kg
- Back:   Open
- Dimensions (W x D x H): 58 x 29 x 45 cm
- Front Grill: detachable
- Speaker Mounting: 1x12 front mounted
Vintage 30 Back in 1986 a new breed of hard rock player was on the rise. To meet the demands of the players and their increasingly hot-rodded amplifiers, we set out to develop a modern speaker, capable of handling much more power and overdrive. To achieve this, we coupled our H magnet (the closest in performance to Alnico) with a new cone and voice coil employing contemporary materials.
Specifications
- Nominal diameter: 12, 305 mm
- Power Rating: 60 W
- Nominal impedance: 8 ohms
- Sensitivity: 100 dB
- Chassis type: Pressed steel
- Voice coil diameter: 1,75, 44,5 mm
- Voice coil material: Round copper
- Magnet type: Ceramic
- Magnet weight: 50 oz, 1,42 kg
- Frequency range: 70 - 5000 Hz
- Resonance frequency, Fs: 75 Hz
- DC resistance, Re: 7,3 ohms
236402
Palmer Cabinets are rugged, flexible and affordable guitar cabinets.
- Front-loadable
- Solid workmanship
- Includes:
- Connection plate with labelling fields
- Connecting cable
- Fastening screws
- Number of speaker openings: 2
- For speaker diameter: 12
- Connectors on connector plate: 2 x input mono/stereo
- Connector type: 6.3 mm jack
- Type of speaker installation: Front-loaded
- Front grill removable: Yes
- Back: Closed
- Acoustic installation (inside): No
- Front grill material: cloth
- Cabinet material: Particle board
- Cabinet covering: Imitation leather
- Baffle material: MDF
- Width: 710 mm
- Height: 480 mm
- Depth: 295 mm
281920
Palmer cabinets are rugged, flexible and affordable guitar cabinets. The main features are:
- Front-mounted speakers
- Detachable grill
- Solid workmanship
- Speaker mount and quality check carried out in Germany
- Cabinet impedance (mono): 8 ohms
- Cabinet impedance (stereo): 16 ohms / speaker
- Power Rating (mono): 160 W
- Power Rating (stereo): 80 W/speaker
- Cabinet weight without speakers: 15,6 kg
- Cabinet weight including speakers: 24 kg
- Back: closed
- Dimensions (W x D x H): 48 x 71 x 29 cm
- Front Grill: Fabric, detachable
- Speaker Mounting: 2 x 12 front mounted
DELTA PRO- 8
Specifications
- Nominal Basket Diameter: 8, 203 mm
- Nominal Impedance: 8 or 16 ohms
- Power Rating: 225 W
- Resonance: 69 Hz
- Usable Frequency Range: 100 Hz - 3.0 kHz
- Sensitivity: 97.8 dB
- Magnet Weight: 59 oz
- Voice Coil Diameter: 2.0, 50.8 mm
286656
The PEBUNT Unterton is a special type of octaver pedal for bass. It can provide straight octave effects but can also create  distorted and weird octave sounds with rich overtones and an interesting life of its own. The PAD switch allows you to use the unit with active and passive basses.
- type: guitar effect pedals
- inputs: 1
- input connectors: 6.3 mm Jack
- input impedance: 1 M Ohm(s)
- outputs: 1
- output connectors: 6.3 mm Jack
- output impedance: 100 k Ohm(s)
- residual noise: -85 dB
- controls: high, mix, low, footswitch, input pad
- display: on/off
- power supply: 9 V DC power supply, 9 V block
- power consumption: 15m A
- cabinet material: sheet steel
- cabinet / housing surface: powder coated
- width: 120 mm
- depth: 120 mm
- height: 60 mm
- weight: 0,75 kg
281979
The PECHOR is an easy to use but velvety sounding Chorus effect. With only three controllers Rate, Depth and Intensity you will easily and quickly find the sound youre looking for Technical Specifications
- Input impedance: 470 K ohms
- Output impedance: 100 k ohms
- Residual noise: -85 dB (all controls centered)
- Controls: RATE, DEPTH, INTENSITY
- Indicator: LED
- Connectors: IN, OUT, DC input (9 V)
- Footswitch: true bybass
- Power requirements: 9 V PP3 or 9 V DC supply (optional)
- Power consumption: 25 mA (9 V DC)
- Dimensions (W x H x D): 120 mm x 120 mm x 56 mm
281981
For guitar players wanting more the Pocket Booster is simply perfect. With just a Gain control the pedal is nonetheless extremely versatile: you can use it to increase the volume of an anaemic amp, or slam the front end for more overdrive. Before dirt boxes, the Pocket Booster generates more saturation and compression; placed at the end of an effects chain it provides a lead level boost. The Pocket Booster works on a 9V battery or optional power adapter, e.g. Palmer PW9V.
- Type: guitar effects
- Number of Inputs: 1
- Input Connections: 6.3 mm jack
- Input Impedance: 1 M ohm
- Number of Outputs: 1
- Output Connections: 6.3 mm jack
- Output Impedance: 100 k ohms
- Intrinsic Noise: -85 dB
- Controls: Gain
- Indicators: On/Off
- Power Supply: power supply 9 V DC, 9 V battery
- Power Consumption: 20 mA
- Housing Material: sheet steel
- Housing Surface: powder-coated
- Width: 60 mm
- Depth: 100 mm
- Height: 55 mm

281994
The PESM Solid Metal is a hard distortion pedal with controls for distortion, output volume, and a 3-band EQ The semi parametric midrange provides a wide variety of sounds from classic rock to extreme metal. Technical Specifications
- Input impedance: 1 M ohms
- Output impedance: 100 K ohms
- Residual noise: -85 dB (all controls centered)
- Controls: HI, MID, MID FREQ, LOW, DIST, VOL
- Indicator: LED
- Connectors: IN, OUT, DC input (9 V)
- Footswitch: true bybass
- Power requirements: 9 V PP3 or 9 V DC supply (optional)
- Power consumption: 18 mA (9V DC)
- Dimensions (W x H x D) 120 mm x 60 mm x 140 mm
282003
The Palmer Monicon L is a precise analog volume control that connects between computers or audio interfaces and self-powered monitor loudspeakers. To prevent signal coloration the circuitry is all passive, the LED indicators and built-in headphone amplifier are powered by the included DC adapter.The Monicon Ls stereo input is on balanced combo sockets, the AUX input features a 3.5 mm TRS jack and RCA connectors. The compact console sports dual outputs for two pairs of monitor speakers and a summed mono output on XLR connectors. The stereo and AUX inputs are alternatively selectable, the outputs can be activated individually and in tandem. Besides the large stereo volume knob the Monicon L provides mono, mute and PFL switches, a 6.35 mm TRS headphone jack as well as separate AUX and headphone level controls for additional convenience.
- Product type: Monitor Controller
- Type: passive
- Channels: 2
- Inputs: 2
- Input connectors: 3.5 mm TRS, XLR, RCA
- Input type: balanced/unbalanced (depending on TS/TRS/XLR connection)
- Max. input level: 20 dBu
- Input impedance: (balanced) 10k, (unbalanced) 5k Ohm(s)
- Outputs: 3
- Output connectors: XLR
- Output type: balanced/unbalanced (depending on TS/TRS connection)
- Max. output level: 20 dBu
- Output impedance: 600 Ohm(s)
- Frequency response: 10 - 40000 Hz
- THD: 0.001 %
- Max. attenuation: (Attenuator) 85, (Attenuator Mute) 112 dB
- Controls: mute, mono, attenuation, input select, output select, pfl source
- Cabinet material: wood, sheet steel
- Cabinet surface: powder coated
- Width: 218 mm
- Height: 77 mm
- Depth: 100 mm
282029
Power supply for all Palmer devices with a 9 V input connector and a maximum power consumption of 500 mA.
- Input Voltage: 100 - 240 V AC 50 Hz
- Output Voltage: 9 V DC, 500 mA regulated
- Polarity negative inside
282054
The PWT 08 is a universal pedalboard power supply with huge 2,000 mA output capacity and 8 standard center negative outlets. Two of these are switchable to 9, 12 or 18 volts, and with the included Y cable they can be combined to a single outlet for 21, 24, 30 or 36 volts maximum output. They are isolated from each other and the remaining outlets. Featuring short circuit and overload protection, the PWT 08 is fully regulated to deliver constant voltage. The unit sports a power on LED, bi-color outlet status LEDs and comes with a set of DC cables and dedicated mains adapter. The PWT 08 is the ideal choice if you have just one or two power hungry pedals or 9 volt effects that can be run on higher DC currents for more dynamics and headroom.
- Product type: power supply
- Type: multiple power supply
- Mains connector: wall wart
- Input voltage: 100 V - 250 V
- Outputs: 5
- Output connectors: 2.1 x 5.5 mm
- Output voltage: 9, 12, 18 V
- Max. output current: 2000 mA
- Isolated outputs: yes
- Polarity: center negative
- Cord length: 25 - 50 cm
- Indicators: Power, Fault
- Controls: Output voltage selector
- Width: 140 mm
- Depth: 80 mm
- Height: 32 mm
- Features: 8 x DC cable, 1 x merge cable
282058
Universal aluminium Pedalboard for the storage of all commercially available floor effects. The cross bars are already covered with Velcro (fleece), a sufficient amount of hook strap is also included. Power supplies and similar peripheral devices can be mounted below the board. For this the Pedalboard features 4 practical hooks on the underside. 2 Elastic bands are supplied - making fixation easyThis set also features a high-quality padded softcase with an accessory compartment and a shoulder strap.
- Material: aluminium
- Surface: powder-coated
- Width of the Cross Bars: 50 mm
- Width: 500 mm
- Height: 35 mm
- Depth: 135 mm
- Accessories (included): soft carrying case with shoulder strap, approx. 1.5m hook tape, 2x black elastic bands
282042
Palmer cabinets are rugged, flexible and affordable guitar cabinets. The main features are:
- Front-mounted speakers
- Detachable grill
- Solid workmanship
- Speaker mount and quality check carried out in Germany
- Cabinet impedance (mono): 8 ohms
- Power Rating (mono): 25 W
- Cabinet weight without speakers: 12 kg
- Cabinet weight including speakers: 17 kg
- Back: Open
- Dimensions (W x D x H): 58 x 29 x 45cm
- Front Grill: detachable
- Speaker Mounting: 1 x 12 front mountedG12M GreenbackThe G12M Greenback has evolved over the decades but still retains its essential, sought-after tone.This version exhibits all the classic G12M characteristics but is voiced with additional broad mid-range attack and restrained top-end to give a forward, punchy attitude to chords and a searing lead tone without fizz.With its well-controlled low-end it can be used singly in low-powered amps, or in multiples for high-power rock heads. Its an ideal speaker to bring drive and definition to modern high gain amps.SPECIFICATION
- Nominal Basket Diameter: 12, 305 mm
- Nominal Impedance: 8 ohms
- Power Rating: 25 W
- Resonance: 75 Hz
- Usable Frequency Range: 75 Hz - 5 kHz
- Sensitivity: 98 dB
- Magnet Weight: 35 oz.
- Voice Coil Diameter: 1.75, 44.5 mm
281906
The PAN08 is a multifunctional device. Each of the four channels can be used independently as an active DI box, line isolation box or booster. The combination socket input accepts unbalanced and balanced signals. The output has dual transformer balanced XLR jacks (front and rear).The signal level can be attenuated by 20 dB for microphone inputs, but can also be boosted in three stages by up to 18 dB for LINE inputs if necessary. With an output level of 12 dBu on a load of 600 with 0.05 % THD / 40 Hz and an output noise level of less than -110 dBu, the unit meets even high professional standards. One special feature that is worthy of mention is battery power. The supply voltage may range from 9 to 18 V. Thus the PAN08 can also be used without mains power outdoors.
281896
Palmer cabinets are rugged, flexible and affordable guitar cabinets. The main features are:
- Front-mounted speakers
- Detachable grill
- Solid workmanship
- Speaker mount and quality check carried out in GermanySpeciafications:
- Speaker diameter: 12 / 305 mm
- Speaker type: Celestion Alnico Blue
- Speaker impedance: 8 ohms
- Mono mode: yes
- Stereo mode: no
- Power output (max.): 15 W
- Type of speaker installation: Front-loaded
- Front grill removable: yes
- Back: closed
- Acoustic insulation (inside): no
- Front grille material: cloth
- Cabinet material: Plywood MDF baffle
- Width: 580 mm
- Depth: 290 mm
- Height: 450 mm
281901
Palmer cabinets are rugged, flexible and affordable guitar cabinets. The main features are:
- Front-mounted speakers
- Detachable grill
- Solid workmanship
- Speaker mount and quality check carried out in GermanySpeciafications:
- Speaker diameter: 12 / 305 mm
- Speaker type: Celestion Creamback
- Speaker impedance: 8 ohms
- Mono mode: yes
- Stereo mode: no
- Power output (max.): 65 W
- Type of speaker installation: Front-loaded
- Front grill removable: yes
- Back: open

- Acoustic insulation (inside): no
- Front grille material: cloth
- Cabinet material: Plywood MDF baffle
- Width: 580 mm
- Depth: 290 mm
- Height: 450 mm
281902
Palmer cabinets are rugged, flexible and affordable guitar cabinets. The main features are:
- Front-mounted speakers
- Detachable grill
- Solid workmanship
- Speaker mount and quality check carried out in Germany
- Cabinet impedance (mono): 8 ohms
- Power Rating (mono): 75 W
- Cabinet weight without speakers: 12 kg
- Back: Open
- Dimensions (W x D x H): 58 x 29 x 45 cm
- Front Grill: detachable
- Speaker Mounting: 1x12 front mounted
EJ1250 - Eric Johnson Signature Model
Eric Johnson, George Alessandro and Eminence have teamed up to create the EJ1250, a 50 watt alnico guitar speaker that delivers amazing vintage tone. Featuring both American and British characteristics, the EJ1250 has punchy lows, warm throaty mids, and articulate highs. The EJ1250 was designed from the past with the future in mind, and is made by hand right here in the USA.
SPECIFICATIONS
- Nominal Basket Diameter 12, 304.8mm
- Nominal Impedance 8 ohms
- Power Rating Watts 75W / Music Program N/A
- Resonance 89Hz
- Usable Frequency Range 70Hz-5.5kHz
- Sensitivity 103
- Magnet Weight 56 oz.
- Gap Height 0.312, 7.92mm
- Voice Coil Diameter 1.75, 44.5mm
281904
Palmer cabinets are rugged, flexible and affordable guitar cabinets. The main features are:
- Front-mounted speakers
- Detachable grill
- Solid workmanship
- Speaker mount and quality check carried out in Germany
- Cabinet impedance (Mono): 8
- Cabinet impedance (Stereo): 16/Speaker
- Power Rating (Mono): 100 W
- Power Rating (Stereo): 50/Speaker
- Cabinet weight without speakers: 15,6 kg
- Back: Closed
- Dimensions (WxDxH): 48x71x29 cm
- Front Grill: Fabric, detachable
- Speaker Mounting: 2 x 12 front mountedCANNABIS REX Coloration : Clean and full, with lots of body and sparkle. Smokey smooth with high-end definition
Genre : Country, Jazz, Classical SPECIFICATION
- Nominal Basket Diameter 12, 304.8 mm
- Nominal Impedance 8 ohms
- Power Rating Watts 50 W / Music Program N/A
- Resonance 96 Hz
- Usable Frequency Range 70 Hz - 5 kHz
- Sensitivity 102
- Magnet Weight 38 oz.
- Gap Height 0.312, 7.92 mm
- Voice Coil Diameter 1.75, 44.5 mm
281941
The PDI03 Palmer speaker simulator combines load impedance, a signal splitter and DI box especially designed for guitars. All functions are optimised for live and recording applications. Instead of being connected to a loudspeaker, the PDI03 is connected directly to the amplifier output. The signal is no longer picked up by a microphone, but after passing through a special filter section is fed directly into a mixing console, tape recorder, etc. This permits power amplifiers to be operated to saturation without troublesome volume problems.Two switches select between the 9 filter presets simulating various types of speakers and enclosures. Open back 2 x 12 combo or 4 x 12 cabinet characteristics and the punch of a full-out stack with a graphic EQ V setting can be selected as well as American or British speakers and ultra brightness.Four paralleled unfiltered outputs are available for further processing. Both filter and line out level are adjustable.For live monitoring, speakers may be connected while the reactive load is automatically switched off. Power handling capacity is 100W RMS without speakers.


281962
1  2  3  4  Nästa »  |  Visa alla